144 Posts

Normal Scott Drone Camp
sythephotoguy60110 Very very very old Gardner Denver air compressors. #worklife #aircompressor #gardnerdenver #pactiv #reynolds 3h

» ログイン to write comment.

9h klcerin
Ludwig Kelsey
Normal KrossliDrilling-Arendal/Norway
krosslidrilling #BredfordDolphin owned by #DolphinDrilling. Aker H3 #drillingrig, built in 1976 and major upgrade 2007 in Gdansk.
#derrick - #ContinentalEmsco 185ft #mudpumps - #GardnerDenver #topdrive - #Varco (#NOV) #BOP - #Shaffer 18 3/4" 10K. by#FredOlsenEnergy
2d

» ログイン to write comment.

makemusic_notwar_ Bad Neustadt 7:30 am in the morning 😎#badneustadt #gardnerdenver #sunshine #spring #warm 3w

» ログイン to write comment.

makemusic_notwar_ I have way to much stuff good night from Bad Neustadt. Traveling for work..... #traveling #stuff #bathroom #badneustadt #tired #goodnight #sleeping #gardnerdenver 3w

» ログイン to write comment.

signpro_ New #GardnerDenver fleet graphics. Designed, supplied and installed by @signpro_ #gardnerdenver #3M #hilux #vehiclegraphics #melbourne #signpro 4w

» ログイン to write comment.

lostpenguintx My other line of work. Welding oilfield pump skids, belt guards, and other necessary fabrications. When I'm not in the office making sales, I'm in the back assembling pumps and welding. #handmadeintexas #aplex #gaso #gardnerdenver #wheatley #plungerpumps #oilfield #oilfieldservice #production 1mon

» ログイン to write comment.

lostpenguintx Big belt guard, 88" long with 53.5" centers. #oilfieldservice #gaso #gardnerdenver #aplex #welding #metalwork #finallyfriday 1mon

» ログイン to write comment.

whitetrash2k13 Installing a blower on a brand spankin new Pete 389
#peterbilt #gardnerdenver
1mon

» ログイン to write comment.

godless_we_run What gems I get to work with haha #gardnerdenver and #caterpillar with fresh rebuilds!! 2mon

» ログイン to write comment.

2mon klcerin
Mayfair Kelsey
klcerin Boatload of ramen for Quanada's Souper Bowl of Caring! #quanada #souperbowlofcaring #gardnerdenver #latergram 2mon

» ログイン to write comment.

nintendocats Time to scoop out all this grease, clean the parts, replace the bearings and fill it with new grease. Lots of grease! #heavyduty #gardnerdenver #airtrack #at3800 2mon
  •   mik3_d Hey Andy how's it going? I have a car question for you man, since u da expert :p My wife's 2005 accord v6. Went to start it and the timing belt snapped. It didn't fully start, never ran. When it turns over now there's a weird knocking sound. I always knew snapping the belt while driving is bad, but what about when trying to start it? I have many options, I have all the parts available at work, but I've never done a timing belt and I don't want to replace mine if my motor is bad. You think my motor is toast? I can buy a replacement Acura tl 3.2 motor with 115k miles from work for about $500 and they bolt right in, same ecu etc just lots of work for me to do by myself. (I don't want to pay too much to fix it, if I reach close to $500 in repair I will buy the 3.2) what would Andy do? Thanks for the advice ahead of time! @nintendocats 2mon
  •   nintendocats If it's making a knocking sound then most likely the Pistons are hitting the valves. I would double check online. Look up the engine code and see if it's an interference engine which means you need a new one. I have never put anything other than the original motor back into a car so I would check on forums and with people who have done it and make sure you know 100% that it will work and if you do put in a new motor make sure you put a new timing belt into it and replace any seals that look hard or could be leaking, like the crankshaft seal, water pump seal, valve cover seals and to be safe a new coolant thermostat. Those seals will be a real pain to do when the motor is sitting in the vehicle. That's what I would do if it was in my shop or it was my own car. And make sure you have all the tools before hand because it really sucks when it's halfway apart in your driveway and you get stuck. @mik3_d 2mon

» ログイン to write comment.

j_carson__ Caught a few great rainbows this morning #texastrout #guadalupe #flyfishtexas @flyfishing #gardnerdenver #crocks 2mon

» ログイン to write comment.

nintendocats Airtrac air powered drill. Interesting to work on. Technology from the early 70's. It's like a tank. #heavyduty #mechanic #gardnerdenver 3mon

» ログイン to write comment.