1oldcj Enjoy the snow o-towners. #fortlauderdale 2w

» LOG IN to write comment.

1oldcj Elevator shaft installation. 5/32" 7018, min of 5/16 bead. #welding 1mon

» LOG IN to write comment.

1oldcj Roof access ladder installed and ready for nobody to climb it 😦#welding #fabrication 1mon

» LOG IN to write comment.

1oldcj Galvanized trailer for property management group. They tried to weld the fenders on but no luck. That's why you call me! #welding 1mon
  •   icweld Fluxcore works good on galvanizing. 1mon
  •   1oldcj Really? I've never tried. Just 3/32" 7018 on these after I group it down. @icweld 1mon

» LOG IN to write comment.

1oldcj No floor? No problem. Cabs rotten on this Dodge 3500. #patches #welding 1mon

» LOG IN to write comment.

1oldcj Pre-trip inspection is critical operators. This wouldn't have been a bad repair if it wasn't for the sheared off shaft inside the gearbox.... #oops 1mon

» LOG IN to write comment.

1oldcj Door installed on shipping container. #welding #seacan 1mon
  •   1oldcj The handle took longer than it took to cut the whole in the container and weld it in. 1mon
  •   matt_wallace Hahaha, that's always the case. 1mon
  •   matt_wallace Did you insulate? 1mon
  •   icweld How tough was this? Ive been wanting to do that to my container. 1mon
  •   1oldcj @icweld worst part is making sure you've drawn a straight line over the corrugated wall. That's a standard steel door and frame with a simple 1.5" square tube frame to weld to. 1mon
  •   1oldcj 75,000 BTU heater gets that place toasty with no insulation @matt_wallace 1mon
  •   icweld Thanks. Looks great. Ive seen some folks use flatbar or angle iron. Good job. 1mon

» LOG IN to write comment.

1oldcj What did you guys plunge for today? #polarbeardip 2mon

» LOG IN to write comment.

1oldcj Poor roofer backed into tree with trailer and snapped all three racks off. #welding #aluminum #ottawa 3mon

» LOG IN to write comment.

3mon 1oldcj
Normal Jason B.
1oldcj Part #2 - bullet proofed it so Tom can't break it... #welding #fabrication #ottawa 3mon

» LOG IN to write comment.

1oldcj Part #1 - folded top link for snow blower 3mon

» LOG IN to write comment.

3mon 1oldcj
Normal Jason B.
1oldcj Replacement railing for parking garage on George St. #welding #fabrication #ottawa 3mon

» LOG IN to write comment.

1oldcj Nelson studded plates and galvanized roof deck for OCH. #welding #ottawa 3mon

» LOG IN to write comment.

1oldcj Stainless steel sewage overflow for Ottawa company. Now polishing and burnishing #fabrication #welding #ottawa 3mon

» LOG IN to write comment.

1oldcj Aluminum dock extension. So you can adjust your bubblers. Ice fishing I'm assuming??? #fabrication #welding #ottawa #bigrideau 3mon

» LOG IN to write comment.

1oldcj Aluminum railing fabrication and install. Glass panels go in later. #aluminum #fabrication #welding #ottawa 3mon

» LOG IN to write comment.

1oldcj Replacement hinges for City of Ottawa waste water treatment plant #fabrication #welding #aluminum #ottawa 3mon

» LOG IN to write comment.

3mon 1oldcj
Normal Jason B.
1oldcj Snow bucket gets back scraper. Did two for him. #welding #ottawa 3mon

» LOG IN to write comment.

1oldcj Under structure I did for a solarium extension in Gatineau park. #welding #fabrication 4mon

» LOG IN to write comment.

1oldcj Finished shot of the #redblacks bar. 4mon

» LOG IN to write comment.